The hardwire kit is the part of a RedTiger install that people either nail in twenty minutes or get badly wrong. The camera is easy — it is the fuse box that separates a parking mode that works from one that drains your battery flat by Thursday morning. This guide covers the two fuses you actually need to find, how to size an add-a-fuse tap, and the circuit choices that cause most of the problems I see.
A hardwire kit has three wires you care about: yellow (constant 12V), red (accessory or switched 12V), and black (ground). The two positive wires tap two different circuits on purpose. The yellow wire keeps the camera alive while the car is parked and feeds parking mode. The red wire tells the camera the ignition is on so it switches to normal recording. If both wires land on the same circuit, the camera cannot tell the difference between parked and driving — and parking mode either never starts or never stops.
The third element is the voltage cutoff, usually a small box or a dip-switch on the kit. RedTiger hardwire kits typically cut power somewhere between 11.6V and 12.4V. That box is your battery insurance, and it only works if the yellow wire is genuinely on a constant circuit. Tapping a switched fuse for the constant wire defeats the cutoff entirely.
Constant, or battery, fuses stay live with the key out. Typical candidates:
Do not trust a diagram. Test with a multimeter set to DC volts. Black probe to a chassis bolt or door hinge, red probe to the exposed metal tab on top of the fuse, both with the key fully out and the car locked and asleep. Wait two minutes after locking — many modern cars keep circuits powered for a while before going to sleep, and a fuse that reads 12V at lock time can read 0V three minutes later.
Avoid tapping anything safety critical: airbags, ABS, fuel pump, or body control modules. If a fuse is labeled SRS or has anything to do with restraints, skip it regardless of how convenient the location is.
Switched fuses read 0V with the key out and 12V with the key in accessory or run. Good choices are the 12V socket, the cigarette lighter, windshield wipers, or the radio head unit. The 12V socket is the friendliest because it is already designed for accessories and usually has a 15A or 20A rating, leaving plenty of headroom for a 2A to 5A camera load.
Test the same way: key out, key in accessory, key in run. You want a fuse that turns on with accessory, not one that only comes alive when the engine cranks. If your car cuts accessory power at start (most do), the camera will reboot briefly on every start — that is normal and harmless.
Add-a-fuse taps hold two fuses: the original fuse for the circuit, and a new fuse for the camera. Get the sizing wrong and you either pop fuses or leave the camera unprotected.
| Load | Camera Fuse | Notes |
|---|---|---|
| Single-channel, no rear cam | 2A | Plenty; most cameras draw under 1A |
| Dual-channel with rear cam | 3A | Rear camera adds roughly 0.3-0.5A |
| Triple-channel / 360 setup | 5A | Keeps headroom for parking mode cycling |
| Camera plus battery pack | 5A-7.5A | Charging draw is the bigger number |
Match the fuse type to the car: most modern vehicles use mini or micro2 blade fuses. Pull an existing fuse and look at it before ordering a tap — buying the wrong size tap is the single most common reason a weekend install turns into a second trip to the parts store.
Orient the tap correctly. The prong that receives the original circuit current should be on the supply side. If you install it backwards, the original circuit is fed through your new camera fuse, which means a blown 2A fuse kills your dome lights. Test by pulling the camera fuse: if the original circuit dies with it, flip the tap 180 degrees.
The black wire needs bare metal, not paint. Find a bolt under the dash near the fuse box, usually a 10mm, back it out, sand the paint to shiny steel, and reinstall with a ring terminal sandwiched against the body. A ground on painted metal will work for weeks and then start causing random reboots, corrupted last files, or parking mode that engages whenever it feels like it. If you cannot find a bolt, self-tapping screws into a structural panel work — into plastic does not.
If your kit has a selector, 12.2V is the sane default for a healthy battery in mild weather. Go to 12.4V if your car sits for several days at a time or you have an older battery. Go to 11.8V only if you drive daily and want maximum parking coverage. Below 11.8V you are borrowing against your battery's cold-start margin, and a car that will not start in a parking garage is a worse outcome than a gap in footage.
If you want a camera to actually cover 24 hours in a parking garage, a hardwire kit on the factory battery is the wrong tool — a dedicated RedTiger dash cam paired with a battery pack is the honest answer, because a pack charges while you drive and discharges in the lot without touching your starting battery.
Fifteen minutes with a multimeter before you tap anything saves you an evening of chasing a dead battery later. The kit itself is simple — the entire outcome depends on which two fuse slots you pick and whether your ground is actually metal.
← Back to Blog