RedTiger Speed Stamp and GPS Overlay: What It Records and When to Turn It Off

Published November 19, 2026 ยท By Julian

What the Speed Stamp Actually Records

The speed overlay on a RedTiger recording is not a live measurement from the camera. It comes from the GPS module, which polls satellites roughly once per second and writes a number into each clip's metadata. When you play footage back in the RedTiger app, that number renders as a small white figure in the corner, usually paired with coordinates and a date. It is convenient, and it is also the single most misunderstood feature on the whole device.

Two things matter here. First, the GPS speed is a lagging value. In a hard braking event, the number on screen at the moment of impact can read three to six mph lower than the vehicle's true speed, because the last satellite fix arrived before the brake pedal went down. Second, GPS speed is measured over ground, not over the drivetrain. If you have oversized tires on a truck, your speedometer reads low and the GPS reads true. If you are in a tunnel, the number freezes at whatever it last saw.

Turning the Overlay On and Off

On most RedTiger units, the setting lives under Settings > Stamp or Settings > GPS Stamp depending on firmware generation. You will typically find four toggles: date, time, coordinates, and speed. A lot of owners leave all four on because it looks thorough. That is usually a mistake for one simple reason: the stamp is burned into the pixels. You cannot remove it later without re-encoding the video, and re-encoding is exactly the kind of edit an insurer's adjuster will squint at.

My recommendation for everyday driving is date, time, and speed on, coordinates off. The coordinates clutter the frame and most people never use them. If you are running a fleet or doing long-haul work where route reconstruction matters, turn coordinates back on and accept the clutter. For anyone who wants a clean frame for vlogging or track footage, turn the entire stamp off and rely on the GPS log file instead.

Why Your Stamp Says the Wrong Thing

Three problems account for nearly every "my dash cam clock is wrong" complaint.

The fix takes ninety seconds: open Settings, set the date and time manually, confirm the time zone matches your actual location, toggle DST if your region observes it, then drive for two or three minutes in open sky so the GPS can confirm and hold the value. Do this once a season and the problem disappears.

Why the Speed Number Sometimes Reads Zero

If your speed overlay shows 0 while you are clearly moving, the GPS module is not getting a fix. Common causes, in order of likelihood:

Test it the cheap way: park in an open lot, power the camera, and watch the GPS icon. It should go from blinking to solid within about sixty seconds on a cold start. If it never goes solid, move the antenna to the top edge of the windshield near the rearview mirror and try again before you assume the module is dead.

Does the Speed Stamp Help or Hurt an Insurance Claim?

It cuts both ways, and it is worth being honest about that.

Help: when someone brake-checks you on a highway and you have footage showing you at 48 mph in a 55 zone, that single number can end a disputed liability argument in one phone call. Adjusted claims with timestamped speed data tend to resolve faster because there is less for the other party's adjuster to argue about.

Hurt: if the stamp shows you at 71 in a 65 at the moment of a collision, you have handed the other side a contributory negligence argument on a silver platter. In a handful of states with comparative fault rules, that number can reduce your payout even when the other driver caused the crash. Some attorneys advise clients to turn the speed stamp off entirely and let the GPS log file hold the data, since the log is not visible on the frame unless someone specifically requests it.

For most drivers the practical answer is: leave speed on for daily driving, and understand what it is showing. If you are a commercial driver with a company that reviews footage, follow company policy over anything you read online.

The GPS Log File Nobody Uses

Every clip with a GPS fix gets a companion data trail โ€” a small text or binary log that records position, heading, and speed at one-second intervals. On RedTiger units this is typically readable through the desktop player, which can plot the route on a map beside the video. This file is far more useful than the burned-in number because it lets you show a speed trend rather than a single frame. "He accelerated from 30 to 52 in under three seconds" is a stronger statement than "he was going 52."

If you are assembling evidence after a crash, pull the entire log for the two minutes before impact, not just the final frame. The desktop player exports this cleanly, and the resulting file is small enough to email to an insurer.

Comparison: Stamp Settings by Use Case

Use CaseDateTimeSpeedCoordinates
Daily commutingOnOnOnOff
Fleet / commercialOnOnOnOn
Rideshare drivingOnOnOffOff
Vlogging / track daysOffOffOffOff
Insurance dispute prepOnOnOnOn

What to Do This Weekend

Grab your car, park outside, and check three things. Open one recent clip and read the timestamp out loud against your phone's clock โ€” if they differ by more than a minute, fix the zone and DST setting. Next, confirm the GPS icon reaches solid lock before you drive off. Finally, decide deliberately whether you want speed burned into your footage, rather than leaving it on because it was on when you unboxed the thing.

If you are still shopping and want a unit with a clean GPS overlay and a usable desktop log viewer, the REDTIGER 4K dual dash cam covers the front and rear and writes a proper GPS trail alongside every clip. Five minutes of setup now saves an argument later.

โ† Back to Blog